The author is making a few great points regarding Installing A Bathtub in general in this content followed below.
Mounting a tub isn't precisely rocket science, however it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult job. If the old bathtub is easily available, the project can move easily; if you need to open up a wall to remove the old tub and also place the brand-new tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the new one. See to it you have certified yourself for the task and are comfortable trying it. As opposed to working with a specialist to take control of a halfway-completed job, it is better to consider employing one prior to you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your restroom if you have currently acquired a new bathtub as well as don't need to transform the plan of your previous supply of water pipes.
Your devices as well as material checklist need to make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Secure the tap in position with the maker given backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap adapters. The previous type ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bath tub until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipe by making a compression join; after that do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks as well as tighten them if necessary. Fill the bathtub as well as additionally check the overflow outlet and also the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait until the bath tub has actually been utilized a minimum of once as this will resolve it right into its last setting.
Getting ready for the Installation
To start with, the sustaining structure supplied with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, causing the water to pass through the wall between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can fracture fairly early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is suggested to fit the floor tiles using water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very intrigued by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you appreciated the blog posting. So long as you appreciated our post plz remember to share it. Thanks for your time. Visit us again soon.
Call Today